Skip to main content Skip to search Skip to main navigation

Carport Emsland 404 x 846 cm with EPDM roof, colour pre-treated slate-grey

Premium quality for your garden
Assembly instructions Data sheet

SKAN HOLZ Carport Emsland


  • Flat-roof carport
  • Exterior dimensions 404 x 846 cm
  • solid structure of high quality glued laminate (BSH spruce)
  • colour-treated in slate grey
  • posts 12 x 12 cm including H-post anchor
  • Roofing of 19 mm-thick roof boarding with EPDM foil
  • Wooden facing with aluminium end edge
  • including rain gutter with downpipe made of anthracite-coated steel



Construction


The construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.


Colour treatment


The colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.


Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.


For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.


Roof covering


The roofing consists of 19 mm-thick timber roof boarding with EPDM foil. This material is suitable for roofs with a low pitch and is characterised by its elastic properties as well as high resistance to weathering and UV radiation. It is installed in a single piece using cold bonding with the adhesive supplied, thereby reducing the number of joints. The material is flexible to work with and is designed for use as roof waterproofing.


Rain gutter

The scope of delivery includes a rain gutter made of galvanised and anthracite-coloured coated metal. The gutter is attached to the carport with sternboard brackets. The gutters are joined together using clamp connectors and the ends are sealed with caps for clamping. Pipes and bends are simply inserted into each other. If gutters or pipes need to be shortened on site, please use a hand saw suitable for steel, not an angle grinder. This will also protect the cut edge from rust.

Would you like a white gutter instead of an anthracite one? No problem. Please make a note of this in your order.


Bracing


The building kit includes 60 cm-long H-post anchors of galvanized flat steel for embedding in concrete in the site-built deep foundation (for size and lay-out see assembly instructions). They firmly connect the posts to the subsurface to ensure high stability.


  • Flat-roof carport
  • Solid structure of glued laminate (BSH spruce)
  • Colour-treated in slate grey
  • Roof boarding with EPDM foil
  • Posts 12 x 12 cm
Anchoring: Post anchors
Base surface: 34.18 m²
Basic length: 738 cm
Basic width: 365 cm
Building volume: 79.81 m³
Color: Slate-grey
Color roofing: Black
Color treatment: Stained
Garantie: 5 years according to our warranty conditions
Included in delivery: H-post anchors, mounting material, assembly instructions
Material: Glulam, spruce
Material roof covering: Roof boards with EPDM rubber roofing
Mounting material: Included
Not inclusiv: Cement
Number of packages: 2
Number of posts: 8 Piece
Passage height (behind): 206 cm
Passage height (front): 223 cm
Passage width: 341 cm
Post length: 220 cm
Post spacing (depth): 230 cm
Post spacing (width): 341 cm
Roof eave height: 225 cm
Roof edging: Wooden fascia with alu edges
Roof overhang (behind): 34 cm
Roof overhang (front): 74 cm
Roof ridge height: 242 cm
Roof shape: Flat roof
Roof slope: backwards
Roof surface: 33.76 m²
Roof thickness: 20 mm
Size: 404 x 846 cm
Slope: 1.2 °
Snow load: 1.25 kN/m²
Surface wood: 142.54 m²
Thickness of posts: 12 x 12 cm
Total height (behind): 225 cm
Total height (front): 242 cm
Total length: 846 cm
Total weight: 940 kg
Total width: 404 cm
Type of installation: Free standing
Wind pressure: 0.95 kN/m²
delivery Note: Road that must support a 38t truck (Germany, mainland)
delivery time: 4-5 weeks
package weight 1: 885 kg
package weight 2: 55 kg
packaging height 1: 85 cm
packaging height 2: 60 cm
packaging length 1: 120 cm
packaging length 2: 60 cm
packaging width 1: 400 cm
packaging width 2: 35 cm
roof overhang (left): 19 cm
roof overhang (right): 19 cm
Skip product gallery

Accessories

Sidewall for glulam carports 230 x 180 cm, spruce, colour pre-treated in slate-grey
Sidewall for glulam carports 230 x 180 cm, spruce, colour pre-treated in slate-grey

Siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 230 cmHeight: 180 cmthickness siding: 2 x 12 cmMaterial: nordic sprucecolour-treated in slate greyPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall, nordic sprucePanels with vertical slatsSuitable for post spacing of 230 cmColour-treated in slate grey

Regular price: €559.00
Sidewall for glulam carports 230 x 220 cm, spruce, colour pre-treated in slate-grey
Sidewall for glulam carports 230 x 220 cm, spruce, colour pre-treated in slate-grey

Siding for installation in a SKAN HOLZ CarportSiding consists of loose boarding in 20 mm thickness, and is not installed until the carport has been completely erected. It provides for increased stability, privacy shield from the side, and protection from wind and overgrown hedges.Product featuresWidth: 230 cmHeight: 220 cmthickness siding: 2 x 12 cmMaterial: nordic sprucecolour-treated in slate greyPhoto galleryAny illustrated terrace roofs, colour treatment and decoration are not included in scope of supply. This involves customer photos, which are to provide you with an impression of the installed condition.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Sidewall, nordic sprucePanels with vertical slatsSuitable for post spacing of 230 cmColour-treated in slate grey

Regular price: €649.00
Post extension 12x12cm in running meters, glulam, colour pre-treated in slate-grey
Post extension 12x12cm in running meters, glulam, colour pre-treated in slate-grey

Do you need longer posts?Order the post extension for your terrace roof or carport of glued laminate. The posts in the building kits are then replaced with longer posts.Product featuresThickness: 12 x 12 cmMaterial: glulam, sprucecolour-treated in slate greyAttention: the surcharge applies per post, and they can only be ordered directly with the carport/terrace roof.Post extension 12x12cm in running meters12 x 12 cmGlued laminateColour-treated in slate grey

Regular price: €54.00
Rear wall siding 352 x 180 cm, spruce, slate grey
Rear wall siding 352 x 180 cm, spruce, slate grey

Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is completely assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 180 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in slate greyPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 180 cmSpruce, colour-treated in slate greyincl. installation post with post anchor

Regular price: €969.00
Rear wall siding 352 x 220 cm, spruce, slate grey
Rear wall siding 352 x 220 cm, spruce, slate grey

Rear wall made of siding for installation in a SKAN HOLZ carportSiding consists of two layers of loose 20 mm thick formwork boards, which are only attached once the carport is fully assembled. It provides increased stability, privacy from the side and protection from e.g. wind or overgrown hedges.Product featuresWidth: 352 cmHeight: 220 cmFormwork thickness: 2 x 12 cmH-post anchor includedMaterial: Nordic spruceColour-treated in slate greyPhoto galleryAny carports, colour treatment and decoration shown are not included in the scope of delivery. These are customer photos, which are intended to give you an impression of the installed state.ConstructionThe construction is made of solid Nordic fir. We use technically-dried, solid spruce wood, scanned for flaws, sorted and weatherproofed by finger-joint bonding according to length. Small fissures, branches and slight twists reflect the character of the materials used.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.incl. installation post and post anchor352 x 220 cmSpruce, colour-treated in slate greyincl. installation post with post anchor

Regular price: €1,069.00
Entrance arch 11,5x12cm , glulam, colour pre-treated in slate-grey
Entrance arch 11,5x12cm , glulam, colour pre-treated in slate-grey

Comfortable entry and exit of carport by mounting one or two round arches. The first post is eliminated by mounting the round arch.Product featuresThickness: 11,5 x 12 cmMaterial: glulam, sprucecolour-treated in slate greycan be mounted left or rightfor carports with an entrance height of 220 cmFor static reasons, cannot be mounted on saddle-roof carports, increased snow load, and post extensions.Entrance arch 11,5x12cmGlued laminateColour-treated in slate grey

Regular price: €679.00
Snow load for single carport (wide), depth up to 846 cm, slate grey
Snow load for single carport (wide), depth up to 846 cm, slate grey

The SKAN HOLZ snow load reinforcement consists of additional rafters that you fit between the existing roof rafters. This reduces the rafter spacing of the carport, thereby increasing its overall load-bearing capacity. The number and size of the rafters vary depending on the carport.The snow load increases the carport’s snow load capacity to 2.5 kN/m².This snow load reinforcement kit contains 6 additional rafters and is compatible with the following models:Carport Emsland 402 (404) x 846 cmBreisgau carport 402 x 840 cmCarport Wendland 409 x 870 cmColour-treated in slate greyPleasenote:The snow load cannot be retrofitted to these carports. Please check the required snow load limit for your residential area before assembly.ConstructionThe construction is made of glued laminate timber, consisting of several dried layers, attached to one another with finger-jointing. They are glued onto one another for weather-resistance. This results in a load-bearing beam which is more resistant to warping and less prone to fissures than naturally grown wood.Colour treatmentThe colour-treated components are coated with a layer of paint at the factory. The coating allows the natural wood grain to remain visible whilst ensuring a uniform surface finish. The components are coated on all sides twice at the factory, after which any excess material is brushed off.Thanks to this factory pre-treatment, the components can be assembled immediately upon delivery. A primer coat prior to assembly is not required. Each kit also includes a quantity of wood stain or paint for touching up cut edges, screw holes or any damage caused during assembly. These areas should be treated in accordance with the installation instructions.For a personalised finish, the visible wooden surfaces can be lightly sanded after assembly and treated with a suitable wood stain or paint. Components that have been colour-treated on all sides may show storage marks due to technical reasons.Snow load increase to sk=2.50 kN/m²Glued laminated timber, colour-treated in slate greySuitable for the Emsland carport (402 (404) x 846 cm)Suitable for the Wendland carport (409 x 870 cm)Suitable for the Breisgau carport (402 x 840 cm)

Regular price: €1,069.00
Roof greening system 400 x 840 cm, for carport Emsland/Wendland
Roof greening system 400 x 840 cm, for carport Emsland/Wendland

Roof greening not only looks good, it also provides many benefits. This roofing protects against the elements, reduces the noise of precipitation, and looks great in a natural environment.Make sure to water regularly during the growth phase (depending on environmental influences). The substrate must be kept sufficiently moist until the roots are established.Included in delivery:Sedum sprouts (mix of 3-4 types, which vary according to time of year)SubstrateFilter fiberstorage mats (Biodrain)Aluminium collection stripNote:Please be aware that roof greening adds a load of approx. 50 kg/m². The structure must have capacity to bear this weight. It may become necessary to mount the increased snow load. It is optionally available. Roof greening is separately supplied and can only be delivered in Germany.Roof greening system400 x 840 cmIncluding substrateincluding filter fiberIncludinig storage mats (Biodrain)

Regular price: €2,959.00
Rainwater pipe flap, Ø 80 mm, with strainer, galvanised steel, anthracite-coated (Mit KI generiert) Mit KI generiert
Rainwater pipe flap, Ø 80 mm, with strainer, galvanised steel, anthracite-coated

Downpipe flap with strainerThe downpipe valve with integrated strainer enables rainwater to be diverted specifically from the downpipe and is ideal for filling rain barrels, cisterns or other collection tanks. The built-in strainer reduces the ingress of leaves, dirt and other coarse debris, thereby helping to ensure better water quality.Thanks to the practical flap mechanism, the water flow can be diverted as required or allowed to pass directly through the downpipe. The robust metal construction with a weather-resistant coating ensures a long service life and an attractive appearance on the building.Technical featuresRainwater downpipe flap with strainer 1 additional pipe clamp Material: Metal Colour: Anthracite Diameter: 80 mmProduct benefits at a glanceIntegrated strainer to reduce leaves and coarse dirt particles Targeted diversion of rainwater into rain barrels or collection tanks Easy switching between water drainage and flow-through mode Robust metal construction for high stability Weather-resistant finish for long-term outdoor use Easy integration into existing downpipe systems Low-maintenance structureThe rainwater pipe valve with integrated strainer is fitted directly into the existing downpipe and allows rainwater to be diverted as required into a rainwater buttrug or another collection tank.Easy to use✅ Shorten the downpipe to the desired length✅ Fit an additional pipe clamp to the longer section of pipe✅ Insert and align the rainwater pipe valve✅ Connect the rainwater tank✅ Open or close the flap as required✅ Clean the built-in strainer regularly to ensure optimum water qualityHandy rainwater pipe flapwith built-in sieveIncluding an additional pipe clampCoated in anthraciteEasy integration into the existing downpipe system

Regular price: €59.00